全國咨詢熱線
生產能力：800/1200 kg/h 電機功率：1.5 kW 切菜規格：800/1200 kg/h 尺寸：1300×600×1050 mm/1800×710×103
一、操作規程：
1、 Operating procedures:
1、使用前，擦拭機器，面對切片機，先將載物臺移更右邊，漏出加油口，向其中加5滴油，多次橫向載物臺，使?jié)櫥途鶆蚍植肌?br />
1. Before use, wipe the machine, face the slicer, move the stage to the right, leak out the oil filler, add 5 drops of oil to it, and cross the stage several times to make the lubricating oil evenly distributed.
2、調節切割厚度，先將厚度調更大，再調需要厚度；調好后將夾具打開，放入物料，夾實，并落下重錘。
2. Adjust the cutting thickness, first adjust the thickness to larger, and then adjust to the required thickness; After adjustment, open the clamp, put in the material, clamp it tightly, and drop the heavy hammer.
3、開機檢查：檢查刀片上是否有異物，檢查刀具護板是否蓋實，檢查磨刀砂輪是否遠離刀片。
3. Start up inspection: check whether there is any foreign matter on the blade, whether the tool guard plate is covered tightly, and whether the grinding wheel is far away from the blade.
4、檢查無誤后，接通電源，打開開關，讓其自動運轉，操作員不能遠離設備，以防發生意外。
4. After checking, turn on the power, turn on the switch and let it run automatically. The operator should not stay away from the equipment to prevent accidents.
5、結束后，先關閉開關，斷電，取下廢料及半成品，打開刀具護板，將刀片及載物臺清理干凈（小心刀片鋒利）。
5. After finishing, first turn off the switch, turn off the power, remove the waste and semi-finished products, open the tool guard, and clean the blade and loading table (be careful that the blade is sharp).
二、注意事項
2、 Precautions
Two.Precautions
Two.Precautions
1、對手輪進行轉動，將標本夾直接升到更高的位置，并轉動手輪將手柄停止轉動，同時將標本夾和手輪都進行鎖定。
1. Rotate the hand wheel to raise the specimen holder to a higher position, turn the hand wheel to stop the handle rotation, and lock both the specimen holder and hand wheel.
2、再?gòu)牡都苌现苯蛹庸で械镀∠?，擦拭干凈后放置在刀盒?nèi)。
2. Then take off the cutting blade from the tool holder, wipe it clean and place it in the tool box.
3、從標本夾上將標本直接的取下。
3. Remove the specimen directly from the specimen holder.
4、對切片機上切片的殘屑進行清理。
4. Clean the scraps on the slicer.
5、更后就是對切片機進行整機的清潔。
5. After that is to clean the whole machine.
注意：我們?cè)谑褂们衅兜臅r(shí)候，一定要格外小心，因?yàn)槠涞度蟹浅５匿h利，如果誤操作的話定會造成嚴重的傷害，不可以直接的用手去接觸切刀片，也不可以將切刀片隨意的亂放。
Note: when we use the slicer, we must