全國咨詢熱線
切片機的外包裝是不銹鋼的，所以我們在日常使用的時候，應當注意不要使用過尖或者是硬的東西碰到其表面，以免劃傷。如果在使用一段時間之后，需要對切片機產品進行清洗的時候，工作人員應當同時卸上下的固定的螺絲，以免在拆掉1個螺絲的時候，發生危險，或者是損壞設備。
The outer package of the slicer is made of stainless steel, so when we use it everyday, we should pay attention not to touch its surface with sharp or hard things to avoid scratches. If it is necessary to clean the slicer products after a period of use, the staff shall remove the fixed screws at the same time, so as to avoid danger or damage to the equipment when removing one screw.
還要注意對切片機做好潤滑護理，應當定期查看其的潤滑情況，在添加潤滑油的時候，應當保持油量足，但不要過量。工作人員應當在每天的工作結束之后，及時將切片機里面是殘留物料清理干凈。并且要注意檢查刀片的磨損情況，如果有問題的話，應及時修理或者是更換。另外，將工作現場清理干凈，而且要注意切斷設備的總電源。
We should also pay attention to the lubrication care of the slicer, check its lubrication condition regularly, and keep enough oil when adding lubricating oil, but not excessive. The staff should clean up the residual materials in the slicer in time after the end of each day's work. And pay attention to check the wear of the blade, if there is a problem, it should be repaired or replaced in time. In addition, the work site shall be cleaned and the main power supply of the equipment shall be cut off.
總之，在我們使用切片機的時候，不但需要按照正確的要求進行操作，還應當盡可能為其提供一個衛生的工作條件和工作環境，以讓切片機的工作性能得到發揮。
In a word, when we use the slicer, we not only need to operate according to the correct requirements, but also should provide a hygienic working condition and working environment for it as far as possible, so that the working performance of the slicer can be brought into play.
除此之外，要想達到良好的切割作用，還需要做好相關的調節工作，并及時換磨損的刀片，實現切割作用。調節時先松開固緊銅柱螺母,其次轉動螺母與銅柱上的厚薄方向調節，厚薄調妥后，要把螺母與銅柱擰緊。
In addition, in order to achieve a good cutting effect, we need to do a good job in the relevant adjustment work, and timely change the worn blade to achieve the cutting effect. When adjusting, first loosen and tighten the copper post nut, then turn the nut to adjust the thickness direction on the copper post. After the thickness is adjusted properly, tighten the nut and the copper post.
換切片機刀片的時候，需要用六角把手插到該機側面孔位，轉動可以調盤方向再換刀；換刀時松掉刀片的二只六角螺絲，插到刀片更換就行，包裝切片作用的順利完成。
When changing the blade of the slicer, it is necessary to insert the hexagonal handle into the hole on the side of the slicer, rotate it to adjust the direction of the wheel, and then change the blade; when changing the blade, loosen the two hexagon screws of the blade, insert it to replace the blade, and the function of packaging and slicing is completed smoothly.
