全國咨詢熱線
1、用手摸調直后的絲手感有小彎，這說明調直模角度大，則把調整用度變小，如果出現大彎，要把調整模的角度增大，如果還不直，就要檢查叼絲輪子高速轉子，與橫切刀的孔，是不是水平位置，這三點必須一線，水平左右不能偏離。
1, with hand touch straightening silk hand feel a small bend, this indicates that the angle of the straightening die is big, then the adjustment is smaller. If there is a big bend, the angle of the adjustment model should be enlarged. If it is not straight, it is necessary to check the high speed rotor of the silk wheel, the hole of the cutter and the horizontal position, and the three points must be on the front line and the level is about the horizontal. It can deviate.
2、開機前必須熟讀使用說明書，并按規定加潤滑油，檢查各緊固件是否擰緊，叼絲輪的旋轉方向是否符合規定的方向，發現問題請及時處理。
2, before starting the machine, you must read the instruction manual well, add lubricating oil according to the regulations, check whether the fasteners are tightened or not, whether the rotation direction of the silk wheel conforms to the prescribed direction, and finds the problem in time.
3、如果出現斷絲頭上有毛刺，可能是橫豎斷絲刀間隙太大，就要調整橫豎刀間隙，如果還不行，在檢查橫豎刀是否磨損嚴重，如果磨損嚴重，就把豎斷絲刀和橫斷絲刀取下，橫斷絲刀在合金砂輪上磨平，豎斷絲刀在一般砂輪上磨平直到鋒利為止。
3. If there is a burr on the broken wire head, it may be that the gap between the vertical cutting tool is too large and the clearance of the vertical knife should be adjusted. If it is not good, the vertical knife and the cross cut knife are taken off if the wear is serious, and the cross cutting knife is smooth on the alloy sand wheel, and the vertical cutter is on the general grinding wheel. Polished until sharp.
4、檢查橫斷絲刀上的螺母是否松動，橫切絲刀與豎切絲刀的間隙調制越小越好，但不要過緊，一般能上下滑動為宜，上沖頭與豎切絲刀的上下間隙一般2-3mm，上沖頭與豎切絲刀的壓量一般為4-5mm。
4. Check the loosening of the nut on the crosscut knife, the smaller the gap modulation of the cross cutting tool and the vertical cutting tool, the better the better, but not too tight, it is suitable to slide up and down, the upper and lower clearance of the top punch and the vertical cutter are generally 2 3mm, and the pressure of the upper punch and the vertical cutter is generally 4 5mm.
5、如果出現連續切斷，可能是拉簧過送，調整拉簧的緊度，也可能是叼絲輪的壓簧送，推不動跑道則需要調整叼絲輪壓簧。
5, if there is a continuous cut off, it may be a pull spring, adjust the tightness of the spring, and may be the reed of the silk wheel.
6.如果出現斷絲，就要檢查叼絲輪上的壓簧是否壓的不緊，或者是叼絲輪上的槽磨損嚴重，調整叼絲輪壓槽后還是不行，就要改變叼絲輪上的槽。
6. if there is a broken wire, it is necessary to check whether the pressure spring on the silk wheel is not tight, or the groove on the silk wheel is badly worn, and the groove on the silk wheel should be changed after adjusting the groove of the silk wheel.
本文的精彩內容來自切丁切塊機詳細內容請點擊我們的網站:http://cnyanan.cn謝謝您的到來!
The highlights of this article are from the chop block cutting machine. Please click on our official website: http://cnyanan.cn, thank you for coming.
